Speedbox 3.0 for Bosch engine

  • Speed limiter: Displays your real speed
  • Maximum speed with assistance: Limit removed
  • Works with INTUVIA, NYON, PURION and KIOX screens.
  • Activation mode: Walk Assist button
  • Compatible with all Bosch engines: Active Line/Plus, Performance/CX from 2014 to 2020 (Gen4)
  • New: Possibility to determine the assistance level: 15, 20, 30 km/h…
  • The use of this device is only allowed on private roads not open to the public.
196,00 €

Using the kit

The SpeedBox 3.0 for BOSCH Active, Performance and CX Line engines is compatible with all Bosch engines, including 2020 models. It is activated by pressing the WALK button on the control panel or via the combination + – + -. As soon as you press, the speed of 9.9 km/h appears for 2 seconds on the dashboard. This tells you that the Speedbox 3 is activated. Your bike’s assistance will no longer be restricted and it will assist you without a speed limit.

To deactivate the Speedbox 2 just press the on WALK button again. “2.5 km/h” is then displayed on your dashboard. This means that your Speedbox 3 is deactivated, the assistance of your BOSCH engine will therefore stop at 25 km/h.

NEW: You can also determine your own assistance level such as 15, 20, 30 km/h… To do this, scan all the assistance modes (Turbo – Sport – Tour – Eco – Tour – Sport – Turbo). The speed limit must be displayed. From there, briefly press the walk button, on the screen you will be able to change the maximum speed (1.5 for 15 km/h, then 2.0 for 20 km/h, etc…) When your bike ride is over, wait for the end of the countdown that appears on your screen before switching off your bike.

How it works in detail

The Speedbox 3 kit for Bosch Active / Performance / CX Line engine from 2014 to 2020 is an electronic module equipped with a microprocessor. It allows the cyclist to be assisted at speeds in excess of the 25 km/h speed limit by unbridling the Bosch engines. The engine continues to assist the cyclist regardless of the actual speed of the bike. This Bosch motor module is very easy to install because the connectors fit perfectly with the original ones (the connectors remain well sealed). Once the motor is reassembled, the module is housed in the casing and therefore totally invisible. Removal of the kit is quite possible by performing the reverse operation.

To activate or deactivate the kit, simply follow the indicated procedure. You do not need to make any settings and the speedbox 3.0 kit is powered by the electricity delivered by your battery. The speedometer displays the actual data (average speed, current speed, kilometres travelled, etc.).

Installation tutorial

  1. Turn off the electric bicycle
  2. Disconnect the battery from the electric bicycle.
  3. Disassemble all parts of the electric bicycle to gain access to the motor connectors.
  4. Disconnect the connectors on the cable from the motor to the speed sensor and from the motor to the display.
  5. Connect the Bosch SpeedBox 3.0 to the disconnected connectors.
  6. Repair the engine.
  7. Connect (plug in) the battery to the electric bicycle. Turn on the electric bicycle.
  8. Activate/deactivate the Bosch SpeedBox 3.0 by pressing the WALK button or via the combination + – + -. Set your own level of support with the Walk button.

Compatibles engines

Speedbox 3.0 kit assembly tutorial on Bosch Performance Line

The Speedbox 3.0 module is installed in the same way as the Speedbox 2. See the video below :

Speedbox 3.0 kit assembly tutorial on Bosch CX Line

The Speedbox 3.0 module is installed in the same way as the Speedbox 2. See the video below :

Further information

removable

No

driving control

Yes

Visible chip

No

brand

motor to unleash

Bosch

Set up difficulty

Easy

Displayed speed

Real values

Max speed

Unlimited

activation button

Walk button

Speedbox 3.0 for Bosch engine

Reviews

There are no reviews yet.

Be the first to review “Speedbox 3.0 for Bosch engine”

Your email address will not be published. Required fields are marked *